Embedded Motion Control 2018 Group 6

Group members

Name:	Report name:	Student id:
Thomas Bosman	T.O.S.J. Bosman	1280554
Raaf Bartelds	R. Bartelds	add number
Bas Scheepens	S.J.M.C. Scheepens	0778266
Josja Geijsberts	J. Geijsberts	0896965
Rokesh Gajapathy	R. Gajapathy	1036818
Tim Albu	T. Albu	19992109
Marzieh Farahani	Marzieh Farahani	Tutor

Initial Design

Link to Initial design report

The report for the initial design can be found here.

Requirements and Specifications

Use cases for Escape Room

1. Wall and Door Detection

2. Move with a certain profile

3. Navigate

Use cases for Hospital Room

(unfinished)

1. Mapping

2. Move with a certain profile

3. Orient itself

4. Navigate

Requirements and specification list

In the table below the requirements for the system and their specification as well as a validation are enumarated.

Functions, Components and Interfaces

The software that will be deployed on PICO can be categorized in four different components: perception, monitoring, plan and control. They exchange information through the world model, which stores all the data. The software will have just one thread and will give control in turns to each component, in a loop: first perception, then monitoring, plan, and control. Adding multitasking in order to improve performance might be applied in a later stage of the project. Below, the functions of the four components are described. What these components will do is described for both the Escape Room Challenge (ERC) and the Hospital Challenge (HC).

In the given PICO robot there are two sensors: a laser range finder (LRF) and an odometer. The function of the LRF is to provide the detailed information of the environment through the beam of laser. The LRF specifications are shown in the table bellow,

Specification	Values	Units
Detectable distance	0.01 to 10	meters [m]
Scanning angle	-2 to 2	radians [rad]
Angular resolution	0.004004	radians [rad]
Scanning time	33	milliseconds [ms]

At each scanning angle point a distance is measured with reference from the PICO. Hence an array of distances for an array of scanning angle points is obtained at each time instance with respect to the PICO.

The three encoders provides the odometry data (i.e) position of the PICO in x, y and &theta directions at each time instance. The LRF and Odometry observers' data plays a crucial role in mapping the environment. The mapped environment is preprocessed by two major blocks Perception and Monitoring and given to the World Model. The control approach to achieve the challenge is through Feedforward, since the observers provide the necessary information about the environment so that the PICO can react accordingly.

Interfaces and I/O relations

The figure below summarizes the different components and their input/output relations.

Overview of the interface of the software structure:

The diagram below provides a graphical overview of what the statemachine will look like. Not shown in the diagram is the case when the events Wall was hit and Stop occur. The occurence of these events will be checked in each state, and in the case they happened, the state machine will navigate to the state STOP. The state machine is likely to be more complex, since some states will comprise a sub-statemachine.

GMapping

For the hospital challenge, the initial state of the environment (i.e. the hospital corridor and the rooms) has to be stored in some way. This can be done in various ways, one of which is mapping. By initially mapping the environment, all changes can be detected by comparing the current state of the environment to the initial mapped environment. Mapping itself can also be done in many ways, gmapping is one example of how mapping can be done. GMapping uses SLAM (Simultaneous Localization and Mapping),

GMapping requires three transitions between coordinate frames to be present, one between the map and the odometry, one between the odometry and baselink and one between baselink and the laser. GMapping provides the first transition but the remaining two have to be developed. The second transition has to be made by a transform broadcaster that broadcasts the relevant information published by the odometry. The final link is merely a static transform between the baselink and the laser and can thereby be published via a static transform publisher. An overview on this is shown in Figure ...

Escape Room Challenge

A simple code was used for the escape room challenge. It is a code that follows a wall. The idea is as follows: Once started PICO first drives in a straight, stopping 30 cm from the first encountered wall. Once this wall detected PICO aligns it's left side with the wall and starts following the wall. Once PICO is following the wall it is testing in each loop if it can turn left, if it can't checks if it can drive forward. If it can't drive forward, meaning that it reached a corner, it will start turning right until it is aligned with the wall in front of it. Then it starts the loop again. This application is very simple but it is robust. Due to the simple geometry of the room, the code should be sufficient for the simple task of getting out.

In the following section, more details are given about the different components of the code (perception, modeling, plan, control, world model, main)

The world model is a class with all the information stored inside. The other components, perception, modeling, plan and control function which are called at a frequency of 20 Hz by the main loop.

- Perception

- Monitoring

- Plan

- Control

Activity Log

An overview over the meeting, activity's and planning can be found at: https://www.overleaf.com/read/vjgrrdnfzhtp