Difference between revisions of "Embedded Motion Control 2018/FAQ"
|Line 130:||Line 130:|
Latest revision as of 09:07, 16 April 2019
When you ran into a problem, try to find the solution here first. If it's not here, try to find an answer by googling your problem, asking fellow students, or, as a very last resort, ask your tutor! If you found a solution, please put it here such that others can use it! Try to be as consise yet descriptive as possible, and try to file your Problem-Solution pair under the correct category (or add a new category if necessary).
To keep a clear overview of this page, a layout structure of Question-Answer (Q-A) is suggested. The following example is used to clarify this structure:
My computer is on fire. Is this a bad thing?
Nah, probably not, the fire will soon die out. Be sure though to commit all your changes to git! Just in case...
What is 2+2?
My laptop is stuck on maximum brightness, how to solve this?
Remark: THE FOLLOWING SOLUTION MAY BREAK YOUR UBUNTU SO PROCEED WITH CAUTION
Open your Terminal. Type
sudo gedit /usr/share/X11/xorg.conf.d/20-intel.conf
A text editor will open. Add the following content
Section "Device" Identifier "card0" Driver "intel" Option "Backlight" "intel_backlight" BusID "PCI:0:2:0" EndSection
Log out and back in. You can now use the brightness controls on your keyboard to change the brightness.
If, however, your login screen does not proceed - you may have added this '20-intel.conf' file which did not exist before -, then we may fix it by deleting this '20-intel.conf' file by doing the following steps:
- At the screen where a small error screen pops up in the middle, enter the terminal by pressing the following combination (CTRL+ALT+F1)
- Now locate the file at "/usr/share/X11/xorg.conf.d/20-intel.conf"
- remove the file via
sudo rm 20-intel.conf
- reboot and you should be able to proceed to log in screen
Ubuntu freezes on login, how to solve this?
The TU/e Zbook laptops of 2016-2017 and 2017-2018 can freeze on login, this is because of issues with the graphical driver.
If the screen freezes before or directly after login, after booting and before you login you can open a virtual console (CTRL+ALT+F1) which works according to the same principles as a terminal. Login with the username and password provided during your installation. Make sure that you have Internet access, otherwise Ubuntu cannot fetch the updates. Now, update your graphical driver with the the commands given below:
sudo apt-get install nvidia-common nvidia-367 sudo apt-get update sudo apt-get upgrade
Reboot your PC. You should be able to log in without any screen-freezes.
If you experience the same freezing problems with a different pc, you can use the following link to find the correct driver to download: https://linuxconfig.org/how-to-install-the-latest-nvidia-drivers-on-ubuntu-16-04-xenial-xerus
Installation of Ubuntu does not work since Ubuntu cannot find any partitions to be placed on, how to solve this?
While following the installation tutorial (https://www.tecmint.com/install-ubuntu-16-04-alongside-with-windows-10-or-8-in-dual-boot/) and leaving both options from Preparing to Install Ubuntu unchecked and hitting on Continue, you will see a different screen than shown in the tutorial considering the Installation type. If this is the case, restart your computer and go to Windows instead of Ubuntu. When in Windows, wait for the tile representing Intel Rapid Storage Technology in the taskbar in the lower right corner. Select this tile with a right mouse button click and select Open Application. Thereafter, a window pops up asking if you want to allow this app to make changes to your device, select yes. A new window appears, click on Performance in the menu above. Under the section Acceleration Configuration, you click on Disable acceleration. When you are asked if you are sure that you want to disable acceleration on the disk or volume, you select yes. Now again go to Ubuntu and your problem should be solved. Now you should be able to follow the rest of the installation tutorial.
Everything related to the programming language
Version control (git)
Everything related to version control using git
installing/updating git with "sudo apt-get install git" results in the following error:
start: Unable to connect to Upstart: Failed to connect to socket /com/ubuntu/upstart: Connection refused No apport report written because the error message indicates its a followup error from a previous failure. dpkg: error processing package runit (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of git-daemon-run: git-daemon-run depends on runit; however: Package runit is not configured yet. dpkg: error processing package git-daemon-run (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: runit git-daemon-run E: Sub-process /usr/bin/dpkg returned an error code (1)
How could I solve this?
A possible solution is to remove the "git-daemon-run" and "runit" file as explained in https://askubuntu.com/questions/631615/unable-to-connect-to-upstart-error-when-installing-git-all (a bug is possible causing the error).
- Remove git-daemon-run
sudo dpkg -r git-daemon-run
- Remove runit
sudo dpkg -r runit
- Now it should install properly the latest version of git via
sudo apt-get install git
Everything related to PICO
My program is not building and running within Qt Creator, how to solve this?
When building the program does not work in Qt creator, but does work in the terminal, the following may fix the problem.
When your project is open, click 'Projects' on the left task bar. Scroll down to 'Build Environment', and expand it (click Details). Now, all the way to the bottom right, click 'Batch Edit'.
Next, open your terminal (ctrl+alt+t), and type
Select the entire output (you probably only need a few relevant variables, but copying everything works fine), and copy (ctrl+shift+c). Paste the entire output in your QT creator Batch Edit window, and click OK. Building with CTRL+B should work now!
If you're still getting undefined reference errors try running the following in the terminal