Embedded Motion Control 2017 Group 6

From Control Systems Technology Group
Jump to navigation Jump to search

About the group

Name Student ID E-mail
Ties Hoenselaar 0857112 t.a.h.hoenselaar@student.tue.nl
Hasan Ilisu 0852221 h.h.ilisu@student.tue.nl
Laura de Jong 0743679 l.s.d.jong@student.tue.nl
Lars Moormann 0861223 l.moormann@student.tue.nl
Bas Straatman 0777325 s.r.t.straatman@student.tue.nl
Jeroen van der Velden 0744957 j.r.v.d.velden@student.tue.nl
Wouter Houtman Tutor w.houtman@tue.nl

Introduction

Robots Pico and Taco

The most memorable part of the course Embedded Motion Control is the 'A-MAZE-ING PICO' challenge, in which software is designed for and implemented into autonomous robots. These autonomous robots, called Pico and Taco, should then be to able to solve a maze with the software in a real-life environment. A maze can contain loops, dead ends and doors that automatically open and close.

Pico will be provided with a basic software layer to carry out primary functions, such as communication and movement. However, to succesfully complete the 'A-MAZE-ING PICO' challenge it is required to design robust software for the changing environment. Several software subsystems will be put to the test in an intermediate challenge. During this challenge, called the corridor competition, Pico must drive through a corridor and take the first exit. With the results of the corridor competition and all its software subsystems Pico should be able to finish the maze challenge. The course Embedded Motion Control is concluded with an overall conclusion.

Software design

The ever-changing environment in reality requires the design of a robust software architecture. It is prefered to design this software architecture before actually programming, because it gives a clear understanding/agreement of the different functions from the start. The first step in creating the software architecture is to specify the requirements that have to be met in order to complete the 'A-MAZE-ING PICO' challenge.


Requirements

In order to achieve the goal, the following requirements have to be met:

  • The robot has to drive through any maze complying with specifications
  • It has to escape the maze within the time limit
  • Collisions with the walls must be avoided
  • Doors must be opened
  • Doors must be recognized in order to achieve the previous requirement
  • The software has to be robust for imperfections in the measurement data and disturbances
  • The robot must not be idle for a long period of time
  • The robot must not ring the bell too often
  • The robot must autonomously solve and navigate through the maze
  • The Software must be started with only one executable


Specifications

The goal and the requirements will be achieved with the following specifications:

Robot

  • The maximum transnational speed of the robot is 0.5 m/s
  • The maximum rotational speed equals 1.2 rad/s
  • The corridor challenge has to be solved in 5 minutes
  • The maze challenge has to be solved in 7 minutes
  • Both challenges have a maximum of two trials
  • The laser range finder (LRF) has a range of 270 degrees
  • The wheel encoders have an unknown accuracy
  • The robot must not be idle for more than 30 seconds

Maze

  • The corners will be approximately 90 degrees
  • The wall distance is 0.5-1.5 meter
  • There is only 1 door in the maze
  • The door starts opening in 2 seconds
  • The door opens if the robot is within 1.3 meter of the door
  • The door is open in 5 seconds
  • The number of rings must not be larger than the number of potential doors
  • The maze may contain loops
  • The maze can contain dead ends


Functions

The software must have the following functions in order to meet the requirements and fulfill the goal:

Function: Description
Drive forward The robot must drive forward unless something, for

example a wall or a corner, is detected

Drive backward The robot must drive a little bit backward if it is unable to rotate
Turn left Make a 90degree left turn
Turn right Make a 90degree right turn
Ring bell The bell must be rang in order to open the door
Localize The robot has to localize itself in the world model, because the

odometry data isn't that accurate

Wait The robot must wait at a dead end in order to check if it is a

door


Components

The following components will be used to reach the goal:

Sensors

  • Laser range finder which uses a laser beam to determine the distance to an object
  • Wheel encoders (odometry) to estimate the position of the robot relative to a starting location

Actuators

  • Holonomic base with omni-wheels
  • Bell to open the door
  • Pan-tilt unit for head (which will not be used)

Computer

  • Intel I7
  • Ubuntu 14.04


Interfaces

Interfaces for Pico/Taco robot in EMC Maze Challenge

The main relations between the interfaces are colored red and can be described as follows:

World model -> Task:The world model can give information about taken paths to the Task
World model -> Skill:The stored observations in the world model are used for movement skills
World model -> Motion:The world model can give data to the actuators
World model -> User interface: The user interface needs the data from the world model to visualize the world model to the human
Task -> World model:The task needs to store information about paths in world model
Skill -> World model :The world model is build from observations
Motion -> World model :The motion can give sensor data about the position to the world model


File:Initial design plan EMC group 6.pdf

Software subsystems

Corridor competition

Maze challenge

Conclusion