Firefly Eindhoven - Operator Manual

From Control Systems Technology Group

(Difference between revisions)
Jump to: navigation, search
(Flight Preparations and Take off)
Line 1: Line 1:
Hello world!
Hello world!
-
== '''Flight Preparations and Take off''' ==
+
== '''Flight Preparations''' ==
Once the simulink model is uploaded in the Cortex of the drone, the drone must be restarted. This is done by removing and re-installing the battery. Its is significant to note that when re-installing the battery, the drone must be kept straight, as it takes a few seconds for the sensors in the drone to calibrate. Not doing this results in accurate sensor data.
Once the simulink model is uploaded in the Cortex of the drone, the drone must be restarted. This is done by removing and re-installing the battery. Its is significant to note that when re-installing the battery, the drone must be kept straight, as it takes a few seconds for the sensors in the drone to calibrate. Not doing this results in accurate sensor data.
 +
 +
== '''Remote Control''' ==
 +
 +
The curiosity drone is operated via a remote control. The numbers in the remote control diagram correspond to the following:
 +
 +
1. SwitchB     
 +
           
 +
2. VrA (not used) 
 +
                   
 +
3. SwitchA   
 +
             
 +
4. Left stick (throttle/yaw)
 +
 +
5. Power button     
 +
     
 +
6. Switch C   
 +
       
 +
7. VrB (not used)
 +
 +
8. Switch D
 +
 +
9. Right stick (roll/pitch)
 +
 +
10. Neck strap eye
 +
 +
11. Power button
 +
 +
12. Touch screen
 +
 +
 +
 +
'' Steps to fly the drone''
 +
 +
1. The remote controller is turned on by pressing both the power buttons.
 +
 +
2. Before the drone is in flight mode, it must be armed. This is done by moving the left stick (4) towards right. This changes the blue light of the drone to red.
 +
 +
3. Once this is done, flip switchA to downward position. This loads the simulink model and the drone is in offboard mode.
 +
 +
4. Flip SwitchD to take off. This sets the drone in hover mode.
 +
 +
5. During this mode right stick can be used to alter the x-y position of the drone.
 +
 +
6. Once the drone is at correct position, switchB can flipped, this runs the simulink model and the trajectory can be executed.
 +
 +
Note: In case of any emergencies, switchD can flipped back and this will cause the drone to land, during the landing position, the user can use the right stick to control the position of drone.
 +
 +
Once the drone has landed, switchB can be flipped back to its initial position. This is followed by switch off switchA and then disarming the drone by keeping the left stick towards left.
 +
 +
The remote controller can be turned off by pressing both the power buttons simultaneously. This opens up a dialog box on the touch screen where touching yes will switch off the remote controller.

Revision as of 00:21, 24 May 2018

Hello world!

Flight Preparations

Once the simulink model is uploaded in the Cortex of the drone, the drone must be restarted. This is done by removing and re-installing the battery. Its is significant to note that when re-installing the battery, the drone must be kept straight, as it takes a few seconds for the sensors in the drone to calibrate. Not doing this results in accurate sensor data.

Remote Control

The curiosity drone is operated via a remote control. The numbers in the remote control diagram correspond to the following:

1. SwitchB

2. VrA (not used)

3. SwitchA

4. Left stick (throttle/yaw)

5. Power button

6. Switch C

7. VrB (not used)

8. Switch D

9. Right stick (roll/pitch)

10. Neck strap eye

11. Power button

12. Touch screen


Steps to fly the drone

1. The remote controller is turned on by pressing both the power buttons.

2. Before the drone is in flight mode, it must be armed. This is done by moving the left stick (4) towards right. This changes the blue light of the drone to red.

3. Once this is done, flip switchA to downward position. This loads the simulink model and the drone is in offboard mode.

4. Flip SwitchD to take off. This sets the drone in hover mode.

5. During this mode right stick can be used to alter the x-y position of the drone.

6. Once the drone is at correct position, switchB can flipped, this runs the simulink model and the trajectory can be executed.

Note: In case of any emergencies, switchD can flipped back and this will cause the drone to land, during the landing position, the user can use the right stick to control the position of drone.

Once the drone has landed, switchB can be flipped back to its initial position. This is followed by switch off switchA and then disarming the drone by keeping the left stick towards left.

The remote controller can be turned off by pressing both the power buttons simultaneously. This opens up a dialog box on the touch screen where touching yes will switch off the remote controller.

Personal tools