Embedded Motion Control 2018 Group 8

From Control Systems Technology Group
Jump to navigation Jump to search

Group members

Name: E-mail Student id:
Srinivasan Arcot Mohanarangan (S.A.M) s.arcot.mohana.rangan@student.tue.nl 1279785
Sim Bouwmans (S.) s.bouwmans@student.tue.nl 0892672
Yonis le Grand y.s.l.grand@student.tue.nl 1221543
Johan Baeten j.baeten@student.tue.nl 0767539
Michaël Heijnemans m.c.j.heijnemans@student.tue.nl 0714775
René van de Molengraft & Herman Bruyninckx René + Herman Tutor

Initial Design

The initial design file can be downloaded by clicking on the following link:File:Initial Design Group8.pdf.

A brief description of our initial design is also given below in this section. PICO has to be designed to fullfill two different tasks, namely the Escape Room Competition (EC) and the Hospital Competition (HC). When either EC or HC is mentioned in the tekst below, it means that the corresponding design criteria is only needed for that competition. If EC or HC is not mentioned, the design criteria holds for both challenges.

Requirements

Functions

Components

Specifications

Interfaces

MORE ON TASK SKILL MOTION ETC????

Escape Room Competition

For the Escape Room Competition, a simple algorithm was used as code. This was done so that the group members without much C++ programming experience could get used to it while the more experienced programmers already worked on the perception code for the Hospital Competition. Therefore, the code used for the Escape Room Competition was a little bit different than the initial design because the aimed perception code was not fully debugged before the Escape Room Competition so that it could not be implemented in the written main code for the Escape Room Competition.

World Model

The data stored in the World Model is small and consists of only three boolians. Those concepts are left, right and front and gets either the value TRUE or FALSE depending on if a obstacle is near that side of the robot. The value of each concept will get refreshed with a frequency of FREQ, deleting all the old data so that no history is stored.

Perception

For the perception of the world for PICO, a simple space recognition code was used. In this code, the LRF data is split into three beam ranges. A left beam range, a front beam range and a right beam range. Around PICO, two circles are plotted. One is the ROBOT_SIZE circle which has a radius so that PICO is just encircled by the circle. The other circle is the MIN_DISTANCE_WALL circle which has a bigger radius than the ROBOT_SIZE circle. For each of the three laser beam ranges, the distance to an obstacle is checked for each beam, and the lowest distance which is larger than the radius of the ROBOT_SIZE circle is saved and checked if it is smaller than the radius of the MIN_DISTANCE_WALL circle. If that is true, the value TRUE is given to the corresponding laser beam range, else the value FALSE is given to that laser beam range. This scan is done with a frequency of FREQ, and by each scan, the previous values are deleted.

Perception of PICO during the Escape Room Competition

Monitoring

For the Escape Room Competition, PICO would only monitor its surroundings between the ROBOT_SIZE circle and the MIN_DISTANCE_WALL circle by giving a meaning to its sensor data (Left, Right, Front). The four meanings are:

  • Nothing: All sensor data has the value FALSE
  • Obstacle: At least one of the sensors has the value TRUE
  • Wall: The Right sensor has value TRUE, while the Front sensor has value FALSE
  • Corner: The Right and Front sensor has value TRUE

The monitored data is only stored for one moment and the old data is deleted and refreshed with each new dataset.

Planning

For the planning, a simple wall following algorithm is used. As design chose, the right wall is chosen as the wall to follow. As initial state it is assumed that PICO sees nothing. PICO will than check if there is actually nothing by searching at its position for an obstacle. If no obstacle is detected at its starting position, PICO will hypothesize that there is an obstacle in front of him and will drive forward until he has validated its hypothesis by seeing an obstacle. This hypothesis will always come true at a certain moment in time due to the restrictions on the world PICO is put into, only if PICO is already alligned to the exit, PICO will fullfill its task directly without seeing an obstacle..

As soon as an obstacle is detected, PICO will assume that this obstacle is a wall and will rotate counter-clockwise until its monitoring says that this obstacle is a wall, so that only the right sensor gives the value TRUE. Due to the fact that the world only consists of walls and corners, and corners are build out of walls, this hypothesis will again always come true when rotating. As soon as only a wall is detected, PICO will drive forward to keep the founded wall on the right.

While following the wall, it can happen that PICO will detect a corner if the front sensor goes of. This can happen if PICO is actually in a corner, or if PICO is not good alligned with the wall so that the front sensor sees the wall that PICO is following. However, in both cases, PICO will rotate counter-clockwise until he only sees a wall so that it will be beter alligned with the wall it was following or if PICO is actually in a corner, it will allign with the other wall that makes up the corner than the wall he was initially following and starts to follow that wall.

Another possibility that can happen if PICO is in its follow the wall state is that PICO lost the wall. This can again happen if PICO is not good alligned with the wall, or if there is an open space in the wall which is a door entry. In both cases, PICO rotates clockwise so that it initially sees a wall or a corner and than starts again following them as usual.

Driving

The Driving for the escaperoom challenge is reletivly simple. PICO has three drives states which are drive_forward, rotate_clockwise and rotate_counterclockwise. Depending on the monitoring, the planning will give which driving state needs to be done by PICO.

The values

The results

More / list on the differences with initial idea

Lessons learned

Hospital Competition Design

World Model

Our strategy is to store the least information as possible, since with less data the system is simplier and most likely more robust. In the worldmodel all the necissary information is stored for the four main functions of the program (perception, monitoring, planning and driving ). This way, there is no communication between the individual functions. They take the worldModel as input, do operations and store data to the worldmodel. The main object in the worldmodel is the rooms vector, which contains all the rooms. In this subclass all the perception and monitoring data regarding that room is stored. So it contains a list of all doors in the room and of all the nodes in the room. The worldmodel also contains flags for the planning and the driving such as it's current task and it's current driving skill.

Nodes

A node is a class containing the data on the (possible) corners. This contains the position of the point (in x and y) relative to Pico. And the 'weight' of the node is stored, this is how many times this node has been perceived. This value comes in to play to hypothesis whether or not this node is a actual corner. To categorize the different types of nodes the following Boolean attributes of the node objects are stored:

Node type Subtype Definition
Open Node The unconfirmed end of a line
closed Node Inward Corner Confirmed intersection of two lines.The angle the node vector (which is always relative to PICO) and each of the intersecting lines is less than 90 degrees at moment of detection.
Outward corner Confirmed intersection of two lines.The angle the node vector (which is always relative to PICO) and at least one of the intersecting lines is more than 90 degrees at moment of detection.

Doors

The doors contain the points from where to where Pico should drive to enter and exit a room. These point are stored as nodes and can be called by the planning to determine the setpoint for the driving skill.

Room

A room consists of a number of nodes and a list of the existing connections. The room thus contains a vector of nodes. Room nodes are updated until the robot leaves the room. The coordinates are than stored relative to the door. This is further described under monitoring. There are two types of hypothesized doors. The strongest hypothesized door is identified by at least one outward corner. The other is identified as adjacent to an open node.

Perception

Firstly the data from the sensors is converted to Cartesian coordinates and stored in the LaserCoord class within Perception. From the testing it became clear that Pico can also detect itself for some data points and that the data at the far ends of the range are unreliable. Therefor the attribute boolean Valid in LaserCoord is set to false in those cases. When using the data it can be decided if the invalid points should be ex- or included.

For the mapping, the corner nodes and nodal connectivity should be determined as defined in the worldmodel. To do this, the laser range data will be examined. The first action is to do a "split and merge" algorithm where the index of the data point is stored where the distance between to points is larger than a certain threshold. The laser scans radially, therefor the further an object is, the further the measurements differ from each other in the Cartesian system. The threshold value is therefor made dependent on the polar distance.

The point before and after each split is hypothesized as a outward corner. This might be a corner, but can also be part of a (unseen) wall. The corner is stored as a invalid node, until it is certain that it is actual outward corner.

Old method

Then in the section between splits the wall is consecutive, however there could be corners inside that section. These corners need to be found.

The original idea was to check if the lines at the begin and end of the section with three hypothesis:

  • They belong to the same line. No further action
  • They are parallel lines. Two corners must lay in this section. Do a recursive action by splitting the section in two.
  • To different lines. The intersection is most likely a corner.

To determine the lines a linear least squares method is used. This is done for a small selection of points at the beginning and the end of the section. If the error from the fit is too large the selections of points is moved until the error is satisfied.

This method proved to be not robust. For horizontal or vertical fits the lines y=ax+b do not produce the correct coefficients. Even with a swap, so x=ay+b this method fails in some cases. It would probably be possible to continue with this method, but it is decided to abandon this search method within the section and adopt to an alternative. This will be a good example of a learning curve.

Current implementation

The method which is currently implimented is inspired by one of last years groups: link to Group 10 2017. The spit and merge can stay in place, the change is the "evaluate sections" function.

interface diagram group 10

Monitoring

The monitoring stage of the software architecture is used to check if it is possible to fit objects to the data of the perception block. For instance by combining four corners into a room. The room is then marked as an object and stored in the memory of the robot. The same is done for doors. This way it is easier for the robot to return to a certain room instead of exploring the whole hospital again. Monitoring is thus responsible for the creation of new room instances, setting of the room attribute explored to 'True' and maintaining the hypotheses of reality. Also the monitoring skill will send out triggers for the planning block if a room is fully explored. It also keeps track of which doors are already passed and which door leads to a new room.

The functions of monitoring are:

  • Door detection
  • Room fully explored
  • Hospital fully explored

Door detection\\ The door detection function uses the information that is stored in the worldmodel to make a door object of two nodes. The function checks for several properties that two nodes have to have to be qualified to be a door. For instance the distance between the nodes should be between 0.5 and 1.5m. They should also not be connected to each other by a wall. When the nodes fulfill all the properties a new door is stored in the current room. This door is marked unexplored so the planning skill knows where to go to. Also an entry point and an exit point are saved with the door. These points are used to safely drive the robot through the door.

add picture here of the vector calculation of the door entry/exitpoint.


Room fully explored \\ The current room that the robot is in is marked as explored when there are three inward corners found in the room. The choice to make the room explored when there are three corners and not four is that it might happen that the entrance to the room is not in the middle of a wall, but at one of the ends and then the room consists of three corners and not four.

add picture here

Hospital fully explored\\ The hospital is marked as fully explored when the hallway has no more unexplored doors and has no more open nodes.


Hypotheses:

When mapping the room the code will maintain two hypothesis of it's reality. The perceived map as described in perception is assumed to be spatially accurate. However PICO is not able to detect and perceive nodes that are behind it. Furthermore perception happens near continuously at 20 Hz. In that time PICO is able to detect which newly found nodes correspond to nodes already stored in memory by checking the distance between the old and the new node. This comparison is less robust when PICO is moving due to larger discrepancies in distance between an the old and new position of a node. For this reason PICO also maintains an odometery-based hypothesis. New positions of the nodes are predicted based on odometer signal and than compared with the perceived nodes to determine which perceived node position correspond to those in memory. Based on this the actual translation and rotation can be determined with three corresponding nodes using the following formula. These nodes need to be in front of PICO to ensure that they are not false-positives:

[math]\displaystyle{ \begin{bmatrix} T \end{bmatrix} = \begin{bmatrix} x_{1,t-\Delta t} & y_{1,t-\Delta t} & 1 \\ x_{2,t-\Delta t} & y_{2,t-\Delta t} & 1 \\ x_{3,t-\Delta t} & y_{3,t-\Delta t} & 1 \\ \end{bmatrix}^{-1} \cdot \begin{bmatrix} x_{1,t} & y_{1,t} & 1 \\ x_{2,t} & y_{2,t} & 1 \\ x_{3,t} & y_{3,t} & 1 \\ \end{bmatrix} }[/math]

Here T is the transformation matrix. The first matrix consists of the x and y coordinates at a previous time step, the second matrix contains the corresponding positions at current time. The transformation matrix is than used to update all the actual room object contained in our world model.

Planning

Driving

Group Review

Results and Discussion

From the start of the project we had all agreed upon the general direction of our design. However partly due to inexperience with programming in C++ we were hesitant to start coding until we had consensus on the exact details of our software architecture. Because of this integration of the software started relatively late resulting in a code that was not fully tested on the day of the challenge. For this reason we were not able to demonstrate the full capability of our design.

We are proud of our extensive design. Our mapping oriented around the determining of landmarks (nodes) which were robustly maintained using multiple hypotheses. All nodes and destinations where stored relative to PICO using no more information than necessary. Our state-machine had a concise logical structure and could determine the next action in a simple and yet robust manner. All relevant information was communicated with the world model. This contained extensive information about the surrounding such as doors, connectivity between the rooms and the next destination.

For the escape room challenge we had a simple implementation of a Wall follower algorithm. We were one of the only three groups to successfully get the robot moving towards the exit. This was also due to our groups early mastery of the git protocol. We had no trouble pulling the code to PICO.

Recommendations

We have a few major recommendations for any group of experienced coding. First, start practicing writing code within the first week of the project. Second have an extensive conversation within the first two weeks of the project. Don´t get stuck to long on details of the design but quickly divide the work and start implementation. Making an extensive design of the data structure is difficult without previous experience. This leads to a "chicken and egg" question where uncertainty in design decisions arises from a lack of experience. For this reason it is impractical to take the linear 'waterfall model' in which implementation coming after design. Instead take the 'agile' or 'concurrent design' approach where implementation and design are done intermittently. Design decisions will become more evident after having coded. Use a modular code structure that can be easily changed. Make each team member in charge of a single module and continuously communicate on the inputs and outputs needed for each module. Flexibility and communication is key. Trying is more important than immediately having the best solution.

Code snippets

The first snippet we like to share is our main function. We used the guidelines for a clean robot program as presented by Herman Bruyninckx. We don't need all the function that were presented. The communication is not needed as a separate function, because this is included in the EMC library. Configuration is not a separate function because all the parameters are set to be constant and can be adjusted in the config.h file. We do have computations which can be subdivided into perception, monitoring and planning. Using these guidelines a structured main file is created which is easy to understand. To further improve performance it would be possible to do certain functions at a higher or a lower rate. This can easily be done by only executing for example the the monitoring and the planning every xth loop.

Secondly, the worldmodel is presented. here the data is actual stored as reported in this page. Most functions are there just to store and to fetch data from the private member attributes, but some do some (small) computations on that data. The larger functions like "add_Node" are in the .c file as to not clutter the header file.

In the perception we implemented a split and merge algorithm. The "evaluateSections" function then finds all corners which are present in that section (of the LRF data) and stores it in the worldmodel. Some clever functionality is a recursive function, so no matter how many corners there are in a section the program will find all. If no new corners are found it can be concluded that:

  • 1. the nodes are connected
  • 2. there is no corner in between the nodes

Therefor a line drawn between the two nodes can be considered a wall.